Search found 8 matches
- Tue Mar 19, 2019 2:24 pm
- Forum: General Discussion
- Topic: Roboclaw solo A30 No Write Setting!!
- Replies: 7
- Views: 5169
Re: Roboclaw solo A30 No Write Setting!!
i now retry and explane to you
tnx
tnx
- Sun Mar 17, 2019 7:02 am
- Forum: General Discussion
- Topic: Roboclaw solo A30 No Write Setting!!
- Replies: 7
- Views: 5169
Roboclaw solo A30 No Write Setting!!
GOOD MORNING
ABOUT SUBJECT
I HAVE UPDATE TODAY NEW FIRMWARE ON SOLO A 30
NOW NO WRITE SETTING
ANY INFO ???
TANKYOU
- Fri Nov 30, 2018 11:31 am
- Forum: General Discussion
- Topic: HELP Roboclaw solo A30
- Replies: 11
- Views: 9448
Re: HELP Roboclaw solo A30
1) I do not have to use on and off for position control! I have to use on and off to start engine and stop engine. 2) position control I have to use it when it starts the motor that connected to an encoder control the speed and the position Sorry for my English I wire pot on S1 and set anlogic mode ...
- Thu Nov 29, 2018 11:04 am
- Forum: General Discussion
- Topic: HELP Roboclaw solo A30
- Replies: 11
- Views: 9448
Re: HELP Roboclaw solo A30
thanks for your reply
but in addition to the start and stop S3
also encoder and pwm and check the position, as I do
but in addition to the start and stop S3
also encoder and pwm and check the position, as I do
- Wed Nov 28, 2018 11:27 am
- Forum: General Discussion
- Topic: HELP Roboclaw solo A30
- Replies: 11
- Views: 9448
Re: HELP Roboclaw solo A30
Thank you for you answer
Yes i use brushed motorI do not want to use potentiometers but digital and encoder and use start and stop standby.
I need use encoder and start and stop. Give me info or schematic example and correct setting!
Tnx 1000
Yes i use brushed motorI do not want to use potentiometers but digital and encoder and use start and stop standby.
I need use encoder and start and stop. Give me info or schematic example and correct setting!
Tnx 1000
- Tue Nov 27, 2018 2:18 pm
- Forum: General Discussion
- Topic: HELP Roboclaw solo A30
- Replies: 11
- Views: 9448
Re: HELP Roboclaw solo A30
Thanks for your answer; my circuit should work like this: when I get the 12v on a load (litle motor) I have to take an optocoupler signal of 5 volts, which in turn will have to start and then stop (S3?) to Roboclaw that drives me a motor brusles (with encoder) that I will check both speed and steps ...
- Mon Nov 26, 2018 1:10 pm
- Forum: General Discussion
- Topic: HELP Roboclaw solo A30
- Replies: 11
- Views: 9448
Re: HELP Roboclaw solo A30
Tankyou
Any help (scheamatic) for start end stop of the motor with an input from 5v to 12v
tnx1000
Any help (scheamatic) for start end stop of the motor with an input from 5v to 12v
tnx1000
- Sun Nov 25, 2018 2:35 pm
- Forum: General Discussion
- Topic: HELP Roboclaw solo A30
- Replies: 11
- Views: 9448
HELP Roboclaw solo A30
566/5000 Good evening I bought a Roboclaw SOLO A30: having a datasheet and a guide book (but the generic guide book for roboclaws); :o I have to connect a motor with encoder and control the start end stop of the motor with an input from 5v to 12v question 1) some examples of wiring diagram would not...