Search found 1594 matches
- Fri May 15, 2015 1:47 pm
- Forum: General Discussion
- Topic: RoboClaw 2x5A v4
- Replies: 3
- Views: 6693
Re: RoboClaw 2x5A v4
The length of time at 10a is purely determined by temperature. As the temperature rises above 25c on the board the maximum peak current is reduced, until at 85c the peak current is 5amps. If you need to run something at higher than 5amps for more than a few seconds I would recommend you use a more p...
- Mon May 11, 2015 8:33 am
- Forum: General Discussion
- Topic: Firmware Update
- Replies: 5
- Views: 11448
Re: Firmware Update
When you open IonMotion, the first screen shown is the Firmware update screen. If you connect your roboclaw to the PC, the software will automatically detect it and update the status on the firmware update screen. If the unit has the latest bootloader you can just click the update firmware button an...
- Mon May 11, 2015 8:30 am
- Forum: General Discussion
- Topic: Getting roboclaw out of bootstrap mode
- Replies: 3
- Views: 10651
Re: Getting roboclaw out of bootstrap mode
Once the board is in bootloader mode you use IonMotion software to update the firmware. Currently there is no other option for updating the firmware. When updating the firmware with IonMotion you do not click the Connect menu item. The first screen that shows in IonMotion(if you are using the latest...
- Tue Apr 14, 2015 8:28 am
- Forum: Velocity and Position Control
- Topic: Question about command 46 (buffered drive)
- Replies: 3
- Views: 6882
Re: Question about command 46 (buffered drive)
Yes, thats one of the uses it was made for. The distance acts like a physical timeout.
- Tue Apr 14, 2015 8:27 am
- Forum: General Discussion
- Topic: Feature request: Reduce the delay before answering queries
- Replies: 1
- Views: 5116
Re: Feature request: Reduce the delay before answering queries
It is an option we are considering adding.
- Tue Apr 14, 2015 8:26 am
- Forum: Velocity and Position Control
- Topic: Command to read both encoders at once?
- Replies: 16
- Views: 23274
Re: Command to read both encoders at once?
OK. i got it now. I will see if I can add a new command that will let you read both values at once.
- Tue Apr 07, 2015 11:06 am
- Forum: Velocity and Position Control
- Topic: Question about command 46 (buffered drive)
- Replies: 3
- Views: 6882
Re: Question about command 46 (buffered drive)
All the distance commands are relative from the current encoder reading. Also if you send a distance command and done send another command before it finishes and the speed at the finish of that command is not zero then the roboclaw will add another distance command that will decelerate the motor to ...
- Tue Apr 07, 2015 11:03 am
- Forum: Velocity and Position Control
- Topic: Command to read both encoders at once?
- Replies: 16
- Views: 23274
Re: Command to read both encoders at once?
There is not currently a command to read both encoders at once. Ill see if I can add one in the next firmware release. With the current system it takes 2 * (1ms + (10*6/38400) = 5.125ms to read both encoders. With a command that could read both at once it would take 1ms + (10 * 10bytes *1/38400) = 3...
- Wed Apr 01, 2015 9:05 am
- Forum: General Discussion
- Topic: Problem with IonMotion
- Replies: 0
- Views: 5384
Re: Problem with IonMotion
Correct. The non-USB capable boards do not support firmware updates. The latest IonMotion software requires the latest firmware. You can send your board in for a firmware update iof you want to use IonMotion with it. The program locks up when you try to connect to the unit because it has older firmw...
- Wed Apr 01, 2015 9:02 am
- Forum: General Discussion
- Topic: Roboclaw 2x30 Choppy Response
- Replies: 2
- Views: 7978
Re: Roboclaw 2x30 Choppy Response
Yes, the default QPPS value will almost never be the correct value for your motor unless oyu happen to run the same motors we set the defaults for and at the same voltage. At a minimum you must always determine the QPPS value. The P,I and D values are very loose. Just about any motor will run with t...