Search found 1555 matches

by Basicmicro Support
Tue Sep 14, 2021 12:29 pm
Forum: General Discussion
Topic: Older Solo 60
Replies: 1
Views: 50

Re: Older Solo 60

1. Please elaborate on the noise. Neither the slightly larger DC Link caps nore the TVS diodes will have much effect on noise. TVS diodes only do anything when the input voltage spikes above their clamping voltage limit which is above 34v on the Solo 60. The larger caps increase the UF slightly but ...
by Basicmicro Support
Tue Sep 14, 2021 12:10 pm
Forum: General Discussion
Topic: Can I read output voltage to motor?
Replies: 3
Views: 996

Re: Can I read output voltage to motor?

Hmm. Reading the PWM isn't a hardware function so I'm not sure how it could be faulty on one unit but not another. It is just a memory value that is read back. If you could elaborate I would appreciate it. Thanks.
by Basicmicro Support
Mon Jul 12, 2021 1:34 pm
Forum: General Discussion
Topic: Odd Speed Readings Of Motor Speeds with 2x7A
Replies: 3
Views: 587

Re: Odd Speed Readings Of Motor Speeds with 2x7A

Please show a printout of the speed values you are seeing here. Along with your code.
by Basicmicro Support
Mon Jul 12, 2021 1:31 pm
Forum: General Discussion
Topic: Using multiple roboclaws with an Arduino
Replies: 1
Views: 373

Re: Using multiple roboclaws with an Arduino

For each Roboclaw you will have a unique class object. That object knows which pins are being used to communciate to the specific Roboclaw. So you can safely use the ReadSpeedM# commands. Since you are using 2 physically different serial ports you can use the same packet address for each roboclaw. Y...
by Basicmicro Support
Mon Jul 12, 2021 1:29 pm
Forum: General Discussion
Topic: MCP Limit switch pullups/downs
Replies: 0
Views: 336

MCP Limit switch pullups/downs

When using a pullup on a MCP I/O pin(or pull down) please keep in mind the internal voltage dividers on each pin. They are 1200ohm series and 2200ohm parallel. This means each I/O has an impedence of 1200ohm and any pullup will need to be stronger than 2200ohm and low enough to pull up above 2v. A 1...
by Basicmicro Support
Mon Jul 12, 2021 1:26 pm
Forum: General Discussion
Topic: RoboClaw Solo 300: issue with RS-485 control on S3
Replies: 2
Views: 424

Re: RoboClaw Solo 300: issue with RS-485 control on S3

RS-485 has a bug in the current firmware. We have been working with a few other people to fix the problem. We currently have a couple different RS-485 adapters we will be testing as soon as time permits. We made some modifications to the firmware so the pin does not change before it should be there ...
by Basicmicro Support
Wed Jun 30, 2021 7:01 pm
Forum: MCL Scripting
Topic: How to use the same input to start and stop?
Replies: 1
Views: 329

Re: How to use the same input to start and stop?

For that you will need to write a small MCL script. The actions can only be used for a single action per I/O.

In the script you will need to keep track of the last state. You will probably need to have a startup routine as well that will determine what the state of the door is.
by Basicmicro Support
Wed Jun 30, 2021 6:59 pm
Forum: MCL Scripting
Topic: What's the difference between safestop and off?
Replies: 1
Views: 184

Re: What's the difference between safestop and off?

With safestop you have to bring the control back to 0 before you do anything else. For example if you safe stop while using an analog joystick.
by Basicmicro Support
Thu Jun 10, 2021 6:28 pm
Forum: General Discussion
Topic: Odd Speed Readings Of Motor Speeds with 2x7A
Replies: 3
Views: 587

Re: Odd Speed Readings Of Motor Speeds with 2x7A

Speed will go to zero when the motor stops. Note the Speed reading is a 1 second average. The ISpeed reading is the 1/300th of a second instant speed. If you have noise on your encoder inputs you could get an instantaneous speed of up to 9.8 million. Enough noise could cause the symptom you describe...
by Basicmicro Support
Thu Jun 10, 2021 6:25 pm
Forum: General Discussion
Topic: RoboClaw 2x45A Tx pin sourcing current
Replies: 1
Views: 475

Re: RoboClaw 2x45A Tx pin sourcing current

The TX pin is limited to 10ma.