Page 1 of 1

Using 3 roboclaw, packet serial, USB

Posted: Tue Apr 14, 2020 12:00 am
by quentin
Hi,

I want to connect three roboclaw in packet serial mode.
I am using a USB to connect to the Master roboclaw. Do I still need a pull up resistor for the incoming signal?
If so, how would I properly wire this up?
also in that set up, I set the first claw to 128, the second to 129 and the third to 130?

I am using actuators on my 3rd roboclaw. While setting them up, I am running into issues setting PIV for them. the ION software tries to tune them and then goes unresponsive. Is this a problem to be expected when using actuators? I still get access to the encoder position and everything and maybe I do not need the PIV settings but I was just wondering.

Thanks,

Quentin

Re: Using 3 roboclaw, packet serial, USB

Posted: Tue Apr 14, 2020 7:35 am
by Basicmicro Support
The USB connected Roboclaw becomes the master controller. Eg Its S1 connects to S2 on the other 2 roboclaws and its S2 connects to S1 on the other 2 roboclaws. Yes you need a pullup. The line connecting the 2 Roboclaws S2 pins to the master Roboclaw needs a pullup. Those 2 Roboclaws also must have multi-unit mode enabled. The master roboclaw must have Relay mode enabled. All three Roboclaws must have different packet serial addresses.

Re: Using 3 roboclaw, packet serial, USB

Posted: Mon May 04, 2020 6:43 am
by quentin
Do the Roboclaws have to run the same version to work with each other?
also, where do I get the 5V to the pull up? from the Claw itself?

Thanks!

Re: Using 3 roboclaw, packet serial, USB

Posted: Mon May 04, 2020 8:04 am
by Basicmicro Support
1. I would recommend having all Roboclaws on the same firmware version. They don't need to be the same Model of Roboclaw though.
2. You can use the Roboclaws 5v for the pullup source. Really I use whatever is convenient.

Re: Using 3 roboclaw, packet serial, USB

Posted: Mon May 04, 2020 12:11 pm
by quentin
That's great. I have been getting an error when trying three roboclaws together:
in _sendcommand,
self._port.write(address.to_bytes(1, 'big'))
AttributeError: 'int' object has no attribute 'to_byte'

I don't suppose you have any ideas on what may be triggering this error?

Thanks again!

Re: Using 3 roboclaw, packet serial, USB

Posted: Tue May 05, 2020 8:00 am
by Basicmicro Support
What version of python are you using? to_bytes is in python3 roboclaw libary, not python2.7. You need to use the appropriate python Roboclaw library for your specific python version, roboclaw.py for python2.7 and roboclaw_3.py for python3+.

Re: Using 3 roboclaw, packet serial, USB

Posted: Wed May 06, 2020 11:29 am
by quentin
Yes,
Thank you for that! Just realised there was some incompatibility from my private set up to the one we were working on, that one being set up on 2.7...
it is all good now!
Thanks for the support!!

Re: Using 3 roboclaw, packet serial, USB

Posted: Wed Jun 17, 2020 1:13 am
by quentin
Hi,

I have now been able to use three roboclaw in packet serial. My pull up to 5V solution is a little experimental but it seems to be properly connected. However, I am getting some latencies that render the robotic arm I am working on, volatile.

I have two actuators on the system that failed the auto tuning for reasons that I do not understand and so I use them only to go with Forward and Backward order from their mechanical min to max. Could that be a factor in the latency?

I also do not have a Logic battery hooked up to the system, could that play a role?
Are there any other factors you believe I should be looking at/investigating?

Thanks

Quentin

Re: Using 3 roboclaw, packet serial, USB

Posted: Wed Jun 17, 2020 8:10 am
by Basicmicro Support
If your communications are intermittent you will be adding significant latencies retrying failed commands.

You'll need to describe what happens when you try autotuning as well as describe your actuators hardware. The autotuner cant tune every setup. Especially low resolution ones or non-linear ones. Those need to manually tuned. Alternatively you can autotune the motor with no load on it and the attach your load(arm) and then tweak the settings.

Re: Using 3 roboclaw, packet serial, USB

Posted: Wed Jul 01, 2020 11:59 pm
by quentin
Hi,

As I have mentinonned before, I am using 3 roboclaws in packet serial. I have the pull up in place and all the addresses. However from the illustration on page 63 of the User Manual, I see that a connection to all grounds is made. Is that true also when using the USB communication? or is it enough to run the S1 S2 cables with the proper pull up to 5V in place?

Thanks

Quentin