broken the third MCP236 after few turns
-
- Posts: 37
- Joined: Wed Jul 31, 2019 7:24 am
broken the third MCP236 after few turns
I have broken the third MCP236 after few turns. I have opened it to check the damage it is another IC that the last time. Probably a current sensor, because the current that I could read by BasicStudio was tot high to be true. please let me know the device.
This is the third in 6 Months. one in October, one in December and one in January.Embarrassing.
This is the third in 6 Months. one in October, one in December and one in January.Embarrassing.
- Attachments
-
- IMG_20210113_144010 - Copy.jpg (254.93 KiB) Viewed 9188 times
- Basicmicro Support
- Posts: 1594
- Joined: Thu Feb 26, 2015 9:45 pm
Re: broken the third MCP236 after few turns
The part you have marked is the opamp for the current sense circuit. It is unclear how you could be damaging that part. Unless there is damage else where(eg the HV regulator and/or 5v regulator, which powers the opamp. Does the unit still power up at all?
How are you powering the MCP? What voltage?
The part in question is: AD8602DRMZ
Note, as I stated above I don't see any way you could be damaging that part without having damaged something further up the chain. It see no high voltages(it is using a low side current shunt resistor).
How are you powering the MCP? What voltage?
The part in question is: AD8602DRMZ
Note, as I stated above I don't see any way you could be damaging that part without having damaged something further up the chain. It see no high voltages(it is using a low side current shunt resistor).
-
- Posts: 37
- Joined: Wed Jul 31, 2019 7:24 am
Re: broken the third MCP236 after few turns
The set up is always the same since the last 2 years so far... power supply 48V-10A SDR-480-48 in series with a Chopper to pull down the voltage in case it goes higher than 51V. So the supply is less than 60V written in the specification which you guarantee.
The moror are brushed with the inductance of 2mH and Resistance of 2 ohm.
The motors are fine and not broken: by oscilloscope, it is possible to see the ripples.
It is unclear how your MCP236 damaged after few turns.
The MCP can still be powered but it measures wrong currents (100 A that physically does not exist). It is not possible to drive a motor now.
The moror are brushed with the inductance of 2mH and Resistance of 2 ohm.
The motors are fine and not broken: by oscilloscope, it is possible to see the ripples.
It is unclear how your MCP236 damaged after few turns.
The MCP can still be powered but it measures wrong currents (100 A that physically does not exist). It is not possible to drive a motor now.
- Basicmicro Support
- Posts: 1594
- Joined: Thu Feb 26, 2015 9:45 pm
Re: broken the third MCP236 after few turns
The only way you can be damaging the current sense circuit is if you are producing a large negative voltage. That shouldn't be possible EITHER. Since there are clamping diodes on the motor channel lines. So only a negative spike on your power supply could cause the damage you are describing has happened three times.
A 2mH and 2ohm armature isn't anything special as far as motors go. Its only 24amps stall current. so I don't see that being the direct cause of this even if I could figure out how the motor could damage the current sense.
I will need more to figure out what could be going on. As detailed as possible, with exact part numbers and schematic. Your chopper, your motor wiring, your power supply etc...
A 2mH and 2ohm armature isn't anything special as far as motors go. Its only 24amps stall current. so I don't see that being the direct cause of this even if I could figure out how the motor could damage the current sense.
I will need more to figure out what could be going on. As detailed as possible, with exact part numbers and schematic. Your chopper, your motor wiring, your power supply etc...